Autoplay
Autocomplete
Previous Lesson
Complete and Continue
Step by step Introduction to SubD in Rhino 7 and 8
1. Overview of this course
1.1 Before you start this course, there are few things you should keep in mind... (2:38)
1.2 What brings SubD to designers?
1.3 Make sure to have the latest toolbar with all the SubD commands (1:33)
1.4 [ Rhino 8 ] The interface of Rhino for Windows and for Mac (0:47)
1.5 [ Rhino 8 ] Few new interesting things about Layers in Rhino 8 (4:44)
2. SubD friendly!
2.1 Control Point and Interpolate Curves SubD friendly (3:32)
2.2 Make curves SubD friendly (0:56)
2.3 How to extrude curves to get a SubD (2:41)
2.4 SubD Review and Q&A
3. Primitives
3.1 SubD Face and SubD Plane (3:41)
3.2 SubD Box, Sphere, Cone, and Cylinder (4:13)
3.3 SubD Loft and Revolve (3:32)
3.4 SubD Sweep 1 rail and Sweep 2 rails (2:04)
3.5 SubD Pipe and Multipipe (4:28)
3.6 SubD Review and Q&A
4. Selecting Sub-objects and setting up filters
4.1 Select all SubD objects in your model (0:59)
4.2 Select Friendly SubD curves (0:36)
4.3 How to select an edge, an edge loop, and a ring of edges in a SubD model (5:22)
4.4 How to select faces from a SubD model and a loop of faces (2:48)
4.5 How to select vertices from a SubD model (2:43)
4.6 Toggle between an Edge or Vertices, and stop all the filters (1:55)
4.7 Back and forth between Flat/Box Mode and SubD mode (1:32)
4.8 Soft Transform (5:49)
4.9 SubD Offset and Extrude SubD (2:59)
4.10 [ Rhino 8 ] Selecting SubD faces to a boundary (0:54)
4.11 [ Rhino 8 ] Select SubD edges (2:54)
4.12 [ Rhino 8 ] Snap to SubD object (3:01)
4.13 SubD Review and Q&A
5. Let us play with Clay and have fun!
5.1 Remove and add a crease (3:11)
5.2 Insert an edge loop or ring and Slide an edge (4:40)
5.3 Merge two coplanar faces (0:58)
5.4 Insert a point to a mesh or SubD (1:38)
5.5 Delete faces and Stitch SubD or Mesh edges or vertices (3:17)
5.6 Subdivide SubD (0:54)
5.7 Bridge meshes or SubD (also known as Blend Super PRO!) (5:00)
5.7 ... (a) Exercise: This is my table, design your own :-) (7:40)
5.8 Reflect and remove the asymmetric from SubD (5:58)
5.8 ... (a) Exercise: Using the Box Mode [TAB] mode and Reflect (6:59)
5.8 ... (b) Exercise: Let us try to model a simple faucet (6:25)
5.8 ... (c) New! in Rhino 7.11 Two-Direction reflection (6:05)
5.9 Bevel a Mesh or SubD (3:25)
5.10 Inset and fill SubD holes [Part #1] (3:10)
5.10 ... (a) Exercise: With Inset and fill SubD holes [Part #2] (5:18)
5.11 Radiate command creates a radial-symmetrical SubD with specified segments (4:14)
5.12 [ Rhino 8 ] SubDcrease, create and modify the weight of "soft crease" (4:18)
5.13 [ Rhino 8 ] Using the SubDcrease and SelSubDEdges, model the handle of a knife. (4:22)
5.14 SubD Review and Q&A
6. Convert to Mesh, Solid, or NURBS
6.1 Convert objects to NURBS (2:49)
6.1 ... (a) Change colors of SubD faces based on the divisions of rectangular quad grids. (2:24)
6.1 ... (b) Pack or unpack SubDs to NURBS (3:12)
6.2 Convert Meshes or Surfaces to SubD (3:55)
6.3 QuadReMesh
6.4 QuadReMesh to reverse engineer a scan
6.5 ... (a) [ Rhino 8 ] ShrinkWrap, a new way of modeling in Rhino 8! (5:52)
6.5 ... (b) [ Rhino 8 ] ShrinkWrap, offset in and out... (7:20)
6.5 ... (c) [ Rhino 8 ] ShrinkWrap, fill holes... (2:34)
6.5 ... (d) [ Rhino 8 ] Nice exercise with SubD and ShrinkWrap (11:02)
6.6 SubD It is time to show off your work!
7. Few exercises and demonstrations from the Pros!
7.1 [ Rhino 8 ] From 2D polylines to a SubD 3D Hand (10:17)
7.2 [ Rhino 8 ] Making a 3D ring using the SubD bridge and reflect commands (7:46)
7.3 Basic 'push & pull' SubD modeling in Rhino 7
7.4 Modeling a SubD sink with the Rhino 7
7.5 Learn how to model a trellis ring using SubD geometry in Rhino 7
7.6 Learn how to model a Fleur-de-lis ring using SubD geometry in Rhino 7
7.7 [ Rhino 8 ] Modeling a coin frame in Rhino 8 (7:23)
7.8 SubD Gumball Party Tricks
7.9 Rhino 7 Sub-D Car Prototype
7.10 The end of this mini course
6.1 ... (a) Change colors of SubD faces based on the divisions of rectangular quad grids.
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock