Autoplay
Autocomplete
Previous Lesson
Complete and Continue
Step by step Introduction to SubD in Rhino 7
1. Overview of this course
1.1 Before you start this course, there are few things you should keep in mind... (2:38)
1.2 What brings SubD to designers?
1.3 Make sure to have the latest toolbar with all the SubD commands (1:33)
2. SubD friendly!
2.1 Control Point and Interpolate Curves SubD friendly (3:32)
2.2 Make curves SubD friendly (0:56)
2.3 How to extrude curves to get a SubD (2:41)
2.4 SubD Review and Q&A
3. Primitives
3.1 SubD Face and SubD Plane (3:41)
3.2 SubD Box, Sphere, Cone, and Cylinder (4:13)
3.3 SubD Loft and Revolve (3:32)
3.4 SubD Sweep 1 rail and Sweep 2 rails (2:04)
3.5 SubD Pipe and Multipipe (4:28)
3.6 SubD Review and Q&A
4. Selecting Sub-objects and setting up filters
4.1 Select all SubD objects in your model (0:59)
4.2 Select Friendly SubD curves (0:36)
4.3 How to select an edge, an edge loop, and a ring of edges in a SubD model (5:22)
4.4 How to select faces from a SubD model and a loop of faces (2:48)
4.5 How to select vertices from a SubD model (2:43)
4.6 Toggle between an Edge or Vertices, and stop all the filters (1:55)
4.7 Back and forth between Flat/Box Mode and SubD mode (1:32)
4.8 Soft Transform (5:49)
4.9 SubD Offset and Extrude SubD (2:59)
4.10 SubD Review and Q&A
5. Let us play with Clay and have fun!
5.1 Remove and add a crease (3:11)
5.2 Insert an edge loop or ring and Slide an edge (4:40)
5.3 Merge two coplanar faces (0:58)
5.4 Insert a point to a mesh or SubD (1:38)
5.5 Delete faces and Stitch SubD or Mesh edges or vertices (3:17)
5.6 Subdivide SubD (0:54)
5.7 Bridge meshes or SubD (also known as Blend Super PRO!) (5:00)
5.7 ... (a) Exercise: This is my table, design your own :-) (7:40)
5.8 Reflect and remove the asymmetric from SubD (5:58)
5.8 ... (a) Exercise: Using the Box Mode [TAB] mode and Reflect (6:59)
5.8 ... (b) Exercise: Let us try to model a simple faucet (6:25)
5.8 ... (c) New! in Rhino 7.11 Two-Direction reflection (6:05)
5.9 Bevel a Mesh or SubD (3:25)
5.10 Inset and fill SubD holes [Part #1] (3:10)
5.10 ... (a) Exercise: With Inset and fill SubD holes [Part #2] (5:18)
5.12 SubD Review and Q&A
6. Convert to Mesh, Solid, or NURBS
6.1 Convert objects to NURBS (2:49)
6.1 ... (a) Change colors of SubD faces based on the divisions of rectangular quad grids. (2:24)
6.1 ... (b) Pack or unpack SubDs to NURBS (3:12)
6.2 Convert Meshes or Surfaces to SubD (3:55)
6.3 QuadReMesh
6.4 QuadReMesh to reverse engineer a scan
6.5 SubD It is time to show off your work!
7. Few exercises and demonstrations from the Pro!
7.1 Intro to SubD geometry in Rhino 7
7.2 Exploring SubD in the Rhino 7
7.3 Basic 'push & pull' SubD modeling in Rhino 7
7.4 Modeling a SubD sink with the Rhino 7
7.5 Learn how to model a trellis ring using SubD geometry in Rhino 7
7.6 Learn how to model a Fleur-de-lis ring using SubD geometry in Rhino 7
7.7 Modeling a Coin Frame in the Rhino 7
7.8 SubD Gumball Party Tricks
7.9 Rhino 7 Sub-D Car Prototype
7.10 How to model a full sport car (Spanish) with SubD
7. The end of this mini course
5.10 ... (a) Exercise: With Inset and fill SubD holes [Part #2]
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock